options for helms...

The Main Sand Box for bertram31.com

Moderators: CaptPatrick, mike ohlstein, Bruce

Post Reply
spencer
Senior Member
Posts: 253
Joined: Feb 10th, '10, 23:50
Location: Boynton Florida

options for helms...

Post by spencer »

When I bought my 31 it was mostly stripped, so I need new helm, ram, etc.

I am using a helm pod from Capt Patrick, so would like a flush mount helm, any recommendations on type of helm/ram that would be used

Thanks

Spencer
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Re: options for helms...

Post by CaptPatrick »

Spencer,

I used the rear mount Sea Star helm on Hancock's boat.

The hydraulic fill plug is located on center of the forward drop down, (little black spot in the image). There are several options as to volume and shaft size/style. I'll let Bruce advise you on those options.

Image
User avatar
PeterPalmieri
Senior Member
Posts: 2612
Joined: Nov 12th, '10, 11:26
Location: Babylon, NY

Re: options for helms...

Post by PeterPalmieri »

Spencer,

Good luck I'd be interested in hearing more about how you plan to lay out the helm. I bought a helm pod but not planning on tackling that project until after the '13 season. I'm still up in the air about how I want to lay it out and have other priorities. I did make some calls and if you want that traditional Rybo style layout Scopinich and Gamefisherman can supply the cluster that integrates with the wheel. No idea if that's the direction your heading but figured I mention it.

I'll be taking notes on the advice your given...

Pete
1969 31 Bertram FBC "East Wind" hull #315939
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Re: options for helms...

Post by CaptPatrick »

Scopinich gage console cluster:

Image
User avatar
PeterPalmieri
Senior Member
Posts: 2612
Joined: Nov 12th, '10, 11:26
Location: Babylon, NY

Re: options for helms...

Post by PeterPalmieri »

Have you done one with those? Does a compass fit above it?
1969 31 Bertram FBC "East Wind" hull #315939
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Re: options for helms...

Post by CaptPatrick »

Peter,

That compass is set on some other boat, there's no room on my console pod, or even the Scorpinich console pod for that matter, for a compass to be mounted directly with either electronics or instrument cluster.

I haven't had anyone make up an instrument cluster for me, but I did one for a customer years ago.

Image

Also did one on Buddy Boy for Jim Bailey:

Image

That page hasn't been updated in years so disregard and pricing that you might see. I'm not even sure I'd tackle another one due to being so dislocated from support industry, like water jet cutting and chroming

Br,

Patrick
Tavis
Posts: 69
Joined: Sep 29th, '12, 08:23

Re: options for helms...

Post by Tavis »

Do any of you guys ever find the singe lever throttle setup, on each side of the helm, difficult if you are needing to change thrust/speed settings while in a turn at the same time? Just asking because I have never run one...
User avatar
bob lico
Senior Member
Posts: 5278
Joined: Jun 29th, '06, 19:22
Location: sayville,long island

Re: options for helms...

Post by bob lico »

Travis the single lever control is the best invention since sliced bread! I captain a 510 Bertram,45 cabo and my own 31 Bertram .the ultimate in fine control especially in backing up because you turn your body around and look down at transom and position of boat with hands on top of levers------------- the ultimate!!!!!!!
capt.bob lico
bero13010473
Post Reply

Who is online

Users browsing this forum: No registered users and 243 guests