pss dripless

The Main Sand Box for bertram31.com

Moderators: CaptPatrick, mike ohlstein, Bruce

Post Reply
User avatar
Charlie J
Senior Member
Posts: 2207
Joined: Jun 29th, '06, 09:14
Location: freeport n.y

pss dripless

Post by Charlie J »

well i think i jinks my self about 6 mouths ago when i said a havent had any problems with the pss after 10 years, noticed they are starting to leak very little after i splashed yeasterday, question is there a way to clean them up, or mabe tighten the stainless coller and put more preasure on the seal. anyone have a sugestion.
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Post by CaptPatrick »

Charlie,

Just adjust the collar back to add some more tension to the bellows hose. Should't need anything more than that. Start with a 1/4", don't over compress...

Br,

Patrick
User avatar
Harry Babb
Senior Member
Posts: 2354
Joined: Jun 30th, '06, 21:45
Location: Fairhope Al
Contact:

Post by Harry Babb »

Charlie
I just purchased a pair of the PSS seals to soon be installed in my 31.

My disqualification in addressing your drip is that this is my first encounter with these seals.....therefore I am not an expert.........I have not done to the PSS seals what I am going to suggest.

My qualifications in addressing your request for advice is that the PSS seals are no more than a version of a Mechanical Seal that is commonly used in industrial applications and I have done this repair to industrial seals. You actually have 2 other mechanical seals on your boat located in the raw water pumps.

These seals are basically pretty simple.......their ability to seal is directly dependent on the surface finish of the 2 mating faces. If you continue to have a drip after adjusting the tension then you will need to disassemble and refinish the sealing surfaces. This assuming that your Bellows is in good shape.

Look around and find a "Mechanical Seal" repair company. In our area I would use the John Crane Company. There are other shops that can do a good job as well.

They will reface the stainless steel "Rotating Body" in a lathe (has to be faced exactly square with the shaft bore) and Lap the carbon graphite "Stationary Body" to a very fine finish and extreme flatness.

A mechanic friend told me a while back that during a tournment one of his customers developed a leak and that he simply took the Rotating Body off of the shaft and resurfaced it by rubbing it on a piece of 400 grit wet or dry sand paper laying on a glass surface. After getting a good surface with the 400 he polished it even further with a piece of 600 grit. The trick is FLAT and SMOOTH............no matter how you get there.

Harry
hb
User avatar
CaptPatrick
Founder/Admin
Posts: 4161
Joined: Jun 7th, '06, 14:25
Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com

Post by CaptPatrick »

Harry,

The composite face, connected to the bellows hose, wears to the face collar, attached to the shaft. Charlie has been running his seals for a decade & that wear has finally released enough tension, originally set when installed, to allow a slight drip. There's no need to, on the PSS, to re-machine anything. They are already faced, from use, concentric with the shafts.

Randall had the same occurance a few years ago, followed the adjustment advice, and no leaks.

Br,

Patrick
User avatar
Harry Babb
Senior Member
Posts: 2354
Joined: Jun 30th, '06, 21:45
Location: Fairhope Al
Contact:

Post by Harry Babb »

I gotcha Pat...............As I said.....I will be installing PSS seals in DeNada hopefully very soon...........Information that you just shared is invaluable. You just saved me a lot of work in a few years after my seals get a bunch of hours on them.

Thanks

Harry
hb
User avatar
randall
Senior Member
Posts: 2623
Joined: Jun 29th, '06, 09:29
Contact:

Post by randall »

man ,patrick.....you have a good memory .
User avatar
Charlie J
Senior Member
Posts: 2207
Joined: Jun 29th, '06, 09:14
Location: freeport n.y

Post by Charlie J »

thank you gentleman, will let you know the out come.i hope its that simple, bellows are in good shape
User avatar
Rawleigh
Senior Member
Posts: 3444
Joined: Jun 29th, '06, 08:30
Location: Irvington, VA

Post by Rawleigh »

Just remember to "burp: them on launch and to occasionally push the bellows back in the water to clean the seal surface of any debris. Sand is not your friend with them!! Other than that I love mine!
Rawleigh
1966 FBC 31
User avatar
randall
Senior Member
Posts: 2623
Joined: Jun 29th, '06, 09:29
Contact:

Post by randall »

ive never "burped" mine, what'r you talkin about?
User avatar
34Hatt
Senior Member
Posts: 275
Joined: Jan 3rd, '07, 11:07
Location: Long Island N.Y
Contact:

Post by 34Hatt »

Burping is mention in the paper work but that is for the low speed one's. If you have the high rpm it has a cooling hose you don't need to burp them. Which is letting the air out by pulling the face away from the collar.
I also have had mine 3 years now since the repower love them.

Paper work recommends replacing the bellows every 7 years. What do most of you all do with that. I have seen ones 10 years old and bellows still looks and feels like new one's.
Dan
1967 Hatteras
34C

EOTL II Rebuild Web Page
Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 146 guests