Prop question

The Main Sand Box for bertram31.com

Moderators: CaptPatrick, mike ohlstein, Bruce

Post Reply
User avatar
billyo
Posts: 48
Joined: Oct 1st, '10, 20:22
Contact:

Prop question

Post by billyo »

It appears that all the help i got from everyone is going to get me out of a jam.but during this dilemma we realize we need to get the correct props for the long haul. I don't know squat about props as my knowledge is in greenhouses (orlandogreenhouse.com) The props on the boat that seemed fine were 3-Blade bronze 18X19. The motors are Yanmar MODEL / HP: 4LHA-STE / 226 hp. TRANSMISSION: ZF HSW630 1.6:1 ratio My question is what should i be looking for in a prop? Pitch,cupping etc.
New member of the Bertram clan.

1970 31' Classic

Hull # 1092104
User avatar
In Memory Walter K
Senior Member
Posts: 2912
Joined: Jun 30th, '06, 21:25
Location: East Hampton LI, NY
Contact:

Post by In Memory Walter K »

You may be inundated with advice but rule of thumb is :
If you know what your engine's WOT is rated at (this is key), take your boat out (warmed up) and nail your throttles to their max position. Look at your tach. Does what your tach says match your engine's rating? If they match, you are properly propped.
If your rpm's are higher than the rating add pitch, adding 1" of pitch will bring you back 100 rpm.
If your rpm's are under the rating, remove an inch of pitch at the rate of 100 rpm's per 1 inch of pitch.
Since you are talking about Yanmars (higher rpm running engines) this may not be an issue. If your fishing demands slooow trolling, at idle are you running slow enough? If OK, fine. If you need to go slower at idle rpm, remove an inch of pitch and add cupping. Tell your prop shop what you are trying to do. Usually cupping will give you back your speed etc., at cruise (higher end of the rpm scale) but let you run slower at the bottom end of the scale.
I have found this formula works whether bronze or Nibral props are used. Hope this helps. Walter
User avatar
Bertramp
Senior Member
Posts: 1430
Joined: Jan 2nd, '09, 14:57
Location: Sag Harbor, NY Fort Lauderdale, FL
Contact:

Post by Bertramp »

There are prop shops here in town (Ft Lauderdale) that should be able to set u up right and maybe even take my spares and make them a "good" set of spares for you.
Try F&J prop 954-377-0119
1970 Bertram Bahia Mar - hull# 316-1003
1973 Bertram 38 (widebody) - hull# BER005960473
Steve "Bertramp" Kelly
User avatar
Marlin
Senior Member
Posts: 478
Joined: Sep 1st, '09, 15:50
Location: Palm Beach, FL

Post by Marlin »

find a good prop shop, that is there business and they should stand behind there recommendation, u dont want to repitch a wheel 2 many times ,they fracture
User avatar
Bertramp
Senior Member
Posts: 1430
Joined: Jan 2nd, '09, 14:57
Location: Sag Harbor, NY Fort Lauderdale, FL
Contact:

Post by Bertramp »

Marlin ....
I am meeting BillyO's Capt this AM and giving him what was my spare set of props. I have an extra set, because of the ones you gave me. What comes around goes around ..... great to be in a place where help and everything else is given so freely.
all the best my "Bertram brothers"
1970 Bertram Bahia Mar - hull# 316-1003
1973 Bertram 38 (widebody) - hull# BER005960473
Steve "Bertramp" Kelly
Post Reply

Who is online

Users browsing this forum: Google [Bot] and 33 guests