bertram31.com

The 31 has 2 engine cowl vents in each gunnel and the previous owner of my boat painted them black. The paint is bubbling and peeling off of them now and they look pretty bad. I think it would look nice to have a highly polished stainless steel cowl vent to replace mine with. Has anyone here found a good stainless replacement cowl vent that does not take any modifications to install? If such a cowl does not exist, I was thinking about stripping the paint and having them chromed? Has anyone gone this route?

JR

Jack

I have not been able to find Stainless vents that I like.

I will say this, they are made of white metal, probably can not be chromed. I would Powder Coat them. Mine were white. I have painted them several times.
Soak the nuts really well. I snapped a couple of the studs on mine. You will not even realize they are twisting until it is too late. Then you can not get them out, need to drill and retap which is tough not much metal in that area.

Tony,

Thanks for the heads up on the studs. What would you soak the nuts/studs in to break them free?

I was thinking that if i have to paint them, maybe I could use a chemical paint stripper to remove the old paint and then roll and tip them in place so they won't need to be removed??

Here are a couple of stainless cowl vents I found online:

https://www.go2marine.com/product/20984 ... e8QAvD_BwE

https://www.go2marine.com/product/86587 ... TEQAvD_BwE

https://www.westmarine.com/buy/perko--c ... nt--255992 (This one is chromed zinc)

I'm not even sure these would fit. I'll have to take a few measurements next time I'm out at the boat.

JR

Jack

I would use any type of corrosion buster. Corrosion X, PB Blaster, Transmission Fluid cut with Mineral Spirits. Snapping the stud was on of those oh !@#$ moments.

Jack

The Sead dog with the Plastic base might be the best bet. Especially for the forward vent. The current vent has a lip on it to keep water that is running down the gunnel from running into the boat.


When I painted mine, I used paint stripper and sand paper where needed. Cleaned them real well, used Mineral spirits then alcohol to make sure they did not have any oil on them. Used rattle can paint. Lasts a couple of years before it starts peeling.


That is why I say powder coat.

Thanks Tony,

I think I may try a pair of the Sea Dog stainless vents with the plastic base and see how that works.

JR

JR, I just finished my replacing my cowl vents yesterday. They are full stainless with 4" collars. I, like you searched high and low and could not find what I wanted. I didn't want plastic. So I found some on Alibaba and yes they are from China. I hate getting stuff from China but we don't make them here so I went ahead and ordered. Minimum order is 5 and total price with freight was $42.00 and change each. They look outstanding. I had to open the holes about 1/8" all around so just a 4" hole saw and repair the screw holes from the original vents. Once I figure out how to post a pic I can shoot one to you. Or let me know your email and I can send a pic. They are really shiny but they are really nice heavy stainless.
Let me know if you are interested.

Wayne

Posting a pic on the site is easy. Use Imgur. Just open an account, and put up the picture on their site. Then you can just link it to this site and it magically appears. Heck if I could do it you can also.

OK, Tony convinced me to try so here goes. Links to the pics of the cowl vents. No pics of them complete but pics of them slipped in where they will be.
They look sharp and with new 4" tubing there should be plenty of air and the water will end up in the bilge where I want it to go.
https://i.imgur.com/Z9STH4A.jpg
https://i.imgur.com/urVzUYD.jpg
https://i.imgur.com/5ykWTX6.jpg

Wayne,

Thanks for the information and pics. They do look great! It's funny, in the second picture, I thought there was a large scratch on your cowl vent, but after taking a closer look, it was the reflection of the outriggers on the boat next to you. Too bad they don't have the same footprint as the original vents--I can see the old screw holes from the old vents on the gunnel in pic #2. I sent you a P.M. with my contact information.

JR

Jack follow Wayne's lead and redo the non skid. That will cover up the old holes.

Jack, I sent you a pm. I was at the west coast rendezvous this weekend so I was out of touch. I polished them up today and forgot to take pics of the finished product. I will do so soon and post them.

I have 4 of these, chromed and never put into service. been wrapped in brown paper for close to 20 years now.
Be a shame to break them up.
they are Not bertram vents they came off my early 60s Century.

i have used these, nice pieces
https://www.vetus.com/en/ventilation/sh ... plate.html

Are you a dealer for them? Looks like dealers are far between up here in the NJ and NY area.

my suppliers usually stock it but I see them all over online .
About $35-$37 each

Thank You

Cowl Vents -- again. Wayne Copland -- I am looking for 2 vents like yours. I searched Alibaba and can't find anything close and nothing close on Google either. I know it has been years, but do you remember the vendor name on Alibaba that supplied them?

I don't really care for the ones with the plastic base. Anybody else find some like Wayne's?

Not available in stainless---- I think the early style clamshell design is ecstatically the prettiest although probably does not flow the most air.


in this pic---facing towards the stern

pic 3/20

https://www.hmy.com/yachts-for-sale/31- ... 3-hei-hei/

Look closely they are running vents against the pillar and on the gunnel. I remember seeing the pillar vents on another boat and I believe they were on the original production boats for the first year or two only.