Cummins repower

MarkD · Post by **MarkD** » Jun 15th, '22, 14:07

Jason:

Can you please share the size and model of those West Marine batteries?

Thanks,
Mark

Snipe · Post by **Snipe** » Jun 16th, '22, 05:29

https://www.westmarine.com/buy/west-mar ... cordNum=12
Thanks Carl I have been trying to do stuff when I can with what I can get!
Mark I added a link for the Battires.

Ironworker · Post by **Ironworker** » Jun 16th, '22, 18:14

Sam's has a group 31 AGM marine battery that I have been using for years. They are roughly $170 or so.

MarkD · Post by **MarkD** » Jun 16th, '22, 20:58

Thanks Jason and Rick. Trying to determine if I should go with a combo battery like Jason’s or deep cycle vs. starting. I have starting batteries now for the Cummins but two are tired.

JeremyD · Post by **JeremyD** » Jun 17th, '22, 07:43

They are expensive - but I went with two of the ODYSSEY 31-PC2150S Heavy Duty batteries. In Florida the heat kills the batteries and I have had good luck with the Odysseys - typically getting twice the lifetime out of them, even the Sams AGM Marine Duracell (if you can find them)

Ironworker · Post by **Ironworker** » Jun 18th, '22, 07:03

I generally change out my Sams AGMs every 3 years and give the old batteries away. Many times the next guys is still using them a couple of years later.

Keep in mind I'm using them in a CC with twins OBs. Its hard to get batteries in the Family Islands in the Bahamas and you don't want to break down out there.

Snipe · Post by **Snipe** » Jun 18th, '22, 17:43

Rick my old batteries were from 2017 (same ones) and still good I just replaced because everything was new! With the port supply account they are pretty heavily discounted.

Snipe · Post by **Snipe** » Jul 10th, '22, 19:52

I have been trying to get stuff done but it is slow going today I finished up mounting exhaust. Most of the wiring I need to just get floating is done. Soda blasting was done this week now for the repairs and barrier coat and bottom paint It would be nice to splash this year just for shake down purposes. Not to mention my sanity it’s been a lot of work not to mention $$$$$ .

[url=https://imgur.com/cVrSMLx]

[/url]

Tony Meola · Post by **Tony Meola** » Jul 10th, '22, 22:38

Nice. Worked out perfectly.

Snipe · Post by **Snipe** » Jul 11th, '22, 04:59

Tony, Not to bad I could have left a little more room for exhaust wrap it is a little tight but I got it in there. Slowly coming along now on to the bottom. See if I can get this thing floating soon.

Carl · Post by **Carl** » Jul 11th, '22, 07:00

Looking great, I hope to see you out there this year!

One warning, if you decide to splash earlier than "done" it may wind up staying "not quite done" as the work takes a backseat to just enjoying for the rest of the season.
I had full expectations of hauling after my initial sea trial...if I made it out of the well, if I made it past my slip, if I made it past my marina, the harbor entrance, to the Buglight marking the channel...but the boat did and found itself in my slip tied up and ready for another day; there she stayed till the weather got cold.
I kinda stayed that way till this year and we are just starting to toy with the interior...just now making minor upgrades to make her presentable and useable although we have been using all along. But used kinda like having the holidays in a home with a renovation project going on.

Ironworker · Post by **Ironworker** » Jul 11th, '22, 19:12

Jason,

Bring you boat to SC. We boat year round. I already have a boat factory set up!

Snipe · Post by **Snipe** » Jul 11th, '22, 19:29

Carl I hear that but at this point I just need a break!!
Rick one of my favorite stops on deliveries is Wrightsville Beach I hope one day to end up down there!!

Carl · Post by **Carl** » Jul 12th, '22, 07:36

Jason-

Oh, you earned a break and should reap the fruits of your work in my opinion!

For me, a splash with a good ride would recharge my batteries, giving me new energy to continue.

And if the boat is left in the water....working on a boat in the water is not the work it is on land. On land the work IS WORK, in the water I find the work has an enjoyable aspect to it...almost therapeutic and I do need therapy.

That said...in the water production and progress can dwindle some.

John Nardi · Post by **John Nardi** » Aug 16th, '22, 07:00

Gorgeous work!!! What size 4 blades are you going to swing??

Snipe · Post by **Snipe** » Aug 16th, '22, 09:26

John thanks! I got a used set of 21x24 Michigan going to start with them. I think they will be a little big but it gives me a starting point. I have talked to someone with the same set up and he is running 20x24 and they are a little small so we will see.

Snipe · Post by **Snipe** » Aug 16th, '22, 09:42

Bottom is done five coats of barrier three coats of bottom paint. Started on the rub rail almost done. This was not the easiest job for sure. I bought it from Danny at high tide and had the corners and bow pre bent. The bow fit ok but corners were unusable i had to cut and miter them thankfully i had enough material to do it. The rail didn’t fit to the boat it wasn’t deep enough i had to grind the whole flange down to make it work. It came out pretty good but once again it was not easy! Should be close to sea trial day soon.

PeterPalmieri · Post by **PeterPalmieri** » Aug 16th, '22, 15:12

Looking good! I don’t ever see myself replacing the rub rail but she looks great, get her over the finish line.

Tony Meola · Post by **Tony Meola** » Aug 16th, '22, 21:30

Wow she is really looking good. Nice work you should be proud.

Snipe · Post by **Snipe** » Aug 17th, '22, 07:12

Thanks tony I hope we can have a get together up this way one day it would be nice to meet some of the guys. I saw Carl this weekend in Atlantic highlands and went over to introduce myself and got a quick tour of his boat!

Amberjack · Post by **Amberjack** » Aug 17th, '22, 10:28

Snipe wrote: ↑Aug 16th, '22, 09:42 This was not the easiest job for sure. I bought it from Danny at high tide and had the corners and bow pre bent. The bow fit ok but corners were unusable i had to cut and miter them thankfully i had enough material to do it. The rail didn’t fit to the boat it wasn’t deep enough i had to grind the whole flange down to make it work. It came out pretty good but once again it was not easy!

Hey Jason, it’s a Bertram 31! They were all built a little, umm, differently? Your rebuild looks top notch. I’m constantly impressed by the talent I see on this forum.

Snipe · Post by **Snipe** » Aug 17th, '22, 11:14

Thanks amberjack I agree they can vary a little from boat to boat. No complaints really it is nice when finished for sure. I Remember a post Capt pat made that said Danny’s rail was for a 46 and wasn’t exactly like stock he also stated the corners couldn’t be bent and had to be mitered. Just trying to help any other guys that are going to tackle this. Nothing that I have done has been plug and play so far but I like the challenges.

Snipe · Post by **Snipe** » Aug 23rd, '22, 06:13

Well I launched Friday and got to do some trials over the weekend as well as some rafting up with friends. I am not done yet but for my sanity I had to go for a ride. The boat performed well I have more work to do but the initial shakedown was great. I have to check the tachometers for accuracy it they are right I might be slightly over propped. There were four guys on board and 200 gal of fuel I ordered a photo tac and will conduct some tests later this week. Right now I make 35 knots wot port engine is 2800 rpm’s and starboard is 2950 rpm’s
At 2400 rpm’s I am around 29.8 knots more pictures and test results to come! It felt amazing to finally take a ride after almost five years!!

Ironworker · Post by **Ironworker** » Aug 23rd, '22, 07:04

Congrats on getting her in the water. Please post some info on fuel burn, prop sizes, etc?

You have a beautiful family.

trace elements · Post by **trace elements** » Aug 23rd, '22, 07:20

Such great news. We are all very happy for you.

jrmoro · Post by **jrmoro** » Aug 23rd, '22, 07:21

Congratulations Jason it must have felt great taking her for a ride after all your hard work.

Carl · Post by **Carl** » Aug 23rd, '22, 07:58

Jason - Awesome news, so glad you were able to get out and run her! I'm sure it has to feel good knowing what you have attained.

I must have missed your sea trial by only a few minutes on Friday. Would have been great to see you fly by...and you would have. We were heading up to the Patton Point Club for the weekend, we got the sea brite bridge for the 7pm opening, so passed highland about 5:30- 6. Hard to tell against the current at no wake. Returned about the same time Sunday...almost headed into the highlands for a swim...but kinda done with boating by then.

The family sure looks happy to have a boat with a wet bottom!

CamB25 · Post by **CamB25** » Aug 23rd, '22, 08:10

Woo Hoo! Looks great!

Stephan · Post by **Stephan** » Aug 23rd, '22, 10:01

Congratulations! This is outstanding news.
Enjoy!
Stephan

DanielM · Post by **DanielM** » Aug 23rd, '22, 10:40

Congratulations. The boat looks great and the family happy. Had to feel great after 5 years.

John F. · Post by **John F.** » Aug 23rd, '22, 12:04

Family looks happy, Snipe looks great and is really fast. Congratulations

moguls2go · Post by **moguls2go** » Aug 23rd, '22, 13:24

Looks great man. I've loved following this thread- you're building such a weapon. Awesome to see photos of her in the water.

Nicely done!!

Tony Meola · Post by **Tony Meola** » Aug 23rd, '22, 20:50

Jason

Congratulations. Best of luck, you did a great job. You should be proud.

So who is the happiest one in the family. You, your wife or son or daughter. By the looks of your son's smile, I bet its him.

Snipe · Post by **Snipe** » Aug 24th, '22, 08:15

Thanks Tony my son is definitely happy he has been down there every day!!
Thank you to everybody it does feel good to be at this point I need to stay focused and keep pushing to the finish line.

cariedl · Post by **cariedl** » Aug 24th, '22, 11:32

Congrats on all your hard work and what I'm sure was a very rewarding shake-down. The boat looks awesome. Can't wait to see here all buttoned up and more pics of you and your family enjoying time on the water.

Tony Meola · Post by **Tony Meola** » Aug 24th, '22, 20:12

Snipe wrote: ↑Aug 24th, '22, 08:15 Thanks Tony my son is definitely happy he has been down there every day!!
Thank you to everybody it does feel good to be at this point I need to stay focused and keep pushing to the finish line.

Jason

Time to make family memories.

scenarioL113 · Post by **scenarioL113** » Aug 25th, '22, 07:56

Good luck Jason...I may have to take a ride to NJ as long as you take me for a ride....I will pay for the fuel...

Snipe · Post by **Snipe** » Aug 25th, '22, 12:26

Any time Frank I got the fuel!

Rocky · Post by **Rocky** » Aug 27th, '22, 09:15

Great job Jason!

bob lico · Post by **bob lico** » Aug 27th, '22, 20:35

pretty much the same installation 16 years ago and it feels like yesterday .we have the same performance numbers both engines can rum 2950 rpm but i have 330 hp and run under prop. hand formed 3 blade 21" x 24 " .nice work enjoy

Tommy · Post by **Tommy** » Aug 29th, '22, 13:43

Congratulations, Jason!

Your patience, determination and perseverance has paid off; she looks fantastic; and the performance numbers speak for themselves!

Snipe · Post by **Snipe** » Apr 26th, '23, 12:24

Still working on the boat but I can’t wait to be back in the water. My marina is doing a new bulked so I have to wait till June 1st. I finished up all the wiring this winter and some other projects. Had to pull the shafts out and have Carl get some new couplings fit them for me. That’s all back together now. Big thanks to Carl they came out great! Just started the sound down in the engine spaces.

Yannis · Post by **Yannis** » Apr 26th, '23, 14:06

Holy crap, how do you make boats like that for crying out loud, why mine is always full with dirty water in the bilge...
Congratulations, you deserve it.

Carl · Post by **Carl** » Apr 26th, '23, 15:49

She's looking real good Jason!

Tony Meola · Post by **Tony Meola** » Apr 26th, '23, 20:16

ll I can say is WOW! Nice work, really nice work. You should be proud of what you built.

DanielM · Post by **DanielM** » Apr 26th, '23, 22:16

A work of Art. Congrats, time to enjoy it.

Snipe · Post by **Snipe** » Apr 27th, '23, 04:56

Thanks guys! Yannis I separated the cabin bilge from the aft bilge to keep it dry and clean. It also keeps he smells out. I still have a bunch of work to do but I can definitely see the light at the end of the tunnel. As you all know it will never stop there is always something to do. Repairs to engine boxes and prep for paint is what’s happening now.

Snipe · Post by **Snipe** » Apr 27th, '23, 06:49

When I bought my boat it had a tuna tower installed and the corners of the engine boxes were cut off so I had to glass them back on. I wanted to do that so I can paint them before I install the sound down on them. The plan was to throw a quick paint job on the windshield and the gunnels and decks but I am running out of time. I was going to try and fix the non skid pattern on top of the boxes but I think it will be a pain so I am thinking just sand it smooth. I want to put cushions there at some point anyway.

Yannis · Post by **Yannis** » Apr 27th, '23, 10:06

Jason,

The non skid on the boxes looks fine, why touch it?
If you put cushions it’s gonna be perfect.
Just touch the corners with some paint now and after the summer you will see...

Rawleigh · Post by **Rawleigh** » Apr 27th, '23, 11:50

I agree with Yannis. Just make a nice even smooth triangle on the corner of each. As long as it is symmetrical it will probably look fine. Unless that will bug you to death . . .