Zero Cavity Pics
Moderators: CaptPatrick, mike ohlstein, Bruce
Zero Cavity Pics
Here is some eye candy of "Zero Cavity"
Did the final tweaking and sea trial today and I got 33.8 knots @ 3950 rpm with full fuel/240 gallons.
Instrument display pic is the Ray Marine e-120 interfaced to the Teleflex can buss system. I setup a full page display as an option for twin engine.
There is also a Teleflex display on a pull out panel on the bridge if you want to use the Ray unit on a full page GPS map or depth.
Additional is a Teleflex display in the stb engine room so you can monitor port and stb vitals while working on them without out having to jump to the bridge.
Both Teleflex displays are setup to show twin engine.
My part in this project was engine systems, controls, wiring and computers, startup, sea trials and tweaking various systems through out. Gen start up and load check.
Did the final tweaking and sea trial today and I got 33.8 knots @ 3950 rpm with full fuel/240 gallons.
Instrument display pic is the Ray Marine e-120 interfaced to the Teleflex can buss system. I setup a full page display as an option for twin engine.
There is also a Teleflex display on a pull out panel on the bridge if you want to use the Ray unit on a full page GPS map or depth.
Additional is a Teleflex display in the stb engine room so you can monitor port and stb vitals while working on them without out having to jump to the bridge.
Both Teleflex displays are setup to show twin engine.
My part in this project was engine systems, controls, wiring and computers, startup, sea trials and tweaking various systems through out. Gen start up and load check.
- Harry Babb
- Senior Member
- Posts: 2354
- Joined: Jun 30th, '06, 21:45
- Location: Fairhope Al
- Contact:
- In Memory of Vicroy
- Senior Member
- Posts: 2340
- Joined: Jun 29th, '06, 09:19
- Location: Baton Rouge, LA
-
- Senior Member
- Posts: 244
- Joined: Jul 1st, '06, 05:37
- Location: bandera / port aransas tx
- Contact:
zero cavity
was wonderin the same ??
- thuddddddd
- Senior Member
- Posts: 1028
- Joined: Jun 29th, '06, 07:42
- Location: N. east Ma, home of fat teddy
- Dave Kosh R.I.P.
- Senior Member
- Posts: 162
- Joined: Jun 30th, '06, 00:10
- Location: Ft. Myers Beach, FL 33931
- Contact:
- mike ohlstein
- Site Admin
- Posts: 2394
- Joined: Jun 29th, '06, 11:39
- Location: So many things seem like no-brainers until you run into someone with no brain.
- Contact:
- CaptPatrick
- Founder/Admin
- Posts: 4161
- Joined: Jun 7th, '06, 14:25
- Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com
Scott,
The panel is in the overhead, forward and center to the inside of the bridge facing. Regino Cabrera & crew did the vast majority of the work in Miami over about a 2 year span. The housing for the panel is glassed in & the overhead is raised about 3" over stock height.
Mike,
Gerry's "Zero Cavity" is a FBC & the head was moved to the V-bert configuration.
Br,
Patrick
The panel is in the overhead, forward and center to the inside of the bridge facing. Regino Cabrera & crew did the vast majority of the work in Miami over about a 2 year span. The housing for the panel is glassed in & the overhead is raised about 3" over stock height.
Mike,
Gerry's "Zero Cavity" is a FBC & the head was moved to the V-bert configuration.
Br,
Patrick
Br,
Patrick
Molon labe
Patrick
Molon labe
- Vince Luciani
- Senior Member
- Posts: 172
- Joined: Jul 1st, '06, 09:50
- Location: Rehoboth Beach, Delaware
- CaptPatrick
- Founder/Admin
- Posts: 4161
- Joined: Jun 7th, '06, 14:25
- Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com
- In Memory Walter K
- Senior Member
- Posts: 2912
- Joined: Jun 30th, '06, 21:25
- Location: East Hampton LI, NY
- Contact:
- Capt Dick Dean
- Senior Member
- Posts: 336
- Joined: Dec 17th, '06, 15:33
- Location: Long Island, N.Y.
- Contact:
Props also have a medium cup.
Yanmar 6LP/315hp, 2:1 gear boxes.
Cruise speed can be anything up to 200 off the top.
24knots@3000 rpm
29knots@3600 rpm
Elbows are factory part.
Pulled the boat this AM but not before taking Tony, my shop mate out for a ride.
He's missed my last two 31 refits and is the only guy I know with arms big enough to have a 46' Bertram tatoo'd on his bicept with great detail.
Yanmar 6LP/315hp, 2:1 gear boxes.
Cruise speed can be anything up to 200 off the top.
24knots@3000 rpm
29knots@3600 rpm
Elbows are factory part.
Pulled the boat this AM but not before taking Tony, my shop mate out for a ride.
He's missed my last two 31 refits and is the only guy I know with arms big enough to have a 46' Bertram tatoo'd on his bicept with great detail.
Capitan:
"Tremendo trabajo.........tienes que haber sacao'muelas como loco verdad?..........quedo preciosa.........ese barquito esta para correr todo el golfo y el este de Estados Unidos.....nuevamente felicitaciones......en relacion a la capota que le vayas a poner.......te recomiendo que vayas a la parte de fotos y busca la lancha No Respirar de Cesar Rivera......sleek, bajita y parece la original.....si quieres mas fotos de esa me avisas para que la veas en detalle......te lo recomiendo.........con esa capota se va a ver regia...."
TRANSLATION:
Great Job! and take a look at the fly bridge "roof"of the boat named No Respirar at the boat pics area....owner Cesar Rivera.....he designed it for his and it looks sleek......almost like the original one.....
"Tremendo trabajo.........tienes que haber sacao'muelas como loco verdad?..........quedo preciosa.........ese barquito esta para correr todo el golfo y el este de Estados Unidos.....nuevamente felicitaciones......en relacion a la capota que le vayas a poner.......te recomiendo que vayas a la parte de fotos y busca la lancha No Respirar de Cesar Rivera......sleek, bajita y parece la original.....si quieres mas fotos de esa me avisas para que la veas en detalle......te lo recomiendo.........con esa capota se va a ver regia...."
TRANSLATION:
Great Job! and take a look at the fly bridge "roof"of the boat named No Respirar at the boat pics area....owner Cesar Rivera.....he designed it for his and it looks sleek......almost like the original one.....
- ZeroCavity
- Senior Member
- Posts: 204
- Joined: Jul 10th, '06, 14:36
- Location: Naples, FL
- John Jackson
- Senior Member
- Posts: 161
- Joined: Jul 19th, '06, 22:39
- Location: Point Pleasant Beach, NJ
- CaptPatrick
- Founder/Admin
- Posts: 4161
- Joined: Jun 7th, '06, 14:25
- Location: 834 Scott Dr., LLANO, TX 78643 - 325.248.0809 bertram31@bertram31.com
John,
I totally encased the original aluminum frames with ~3/16" of fiberglass layup. Each of the three sections were done individually leaving the designed slip joint for re-assembly.
Revels were made with PVC Foam Board & were glassed in so that window glass and acrylic corners would be glazed in from the inside. Both the glass and acrylic were glazed in before taking the units back to Cabrera in Miami for installation on the boat. They were fiberglassed in place, faired & gelcoated for a seamless installation.
Interior flange moldings were fabricated and fitted in fiberglass sheet stock.
For the blow by blow progression see: Glassing Over Bertram 31' Front Aluminum Window Frames
Would I do this again? Probably not... Way too much time and agrivation.
Br,
Patrick
I totally encased the original aluminum frames with ~3/16" of fiberglass layup. Each of the three sections were done individually leaving the designed slip joint for re-assembly.
Revels were made with PVC Foam Board & were glassed in so that window glass and acrylic corners would be glazed in from the inside. Both the glass and acrylic were glazed in before taking the units back to Cabrera in Miami for installation on the boat. They were fiberglassed in place, faired & gelcoated for a seamless installation.
Interior flange moldings were fabricated and fitted in fiberglass sheet stock.
For the blow by blow progression see: Glassing Over Bertram 31' Front Aluminum Window Frames
Would I do this again? Probably not... Way too much time and agrivation.
Br,
Patrick
Br,
Patrick
Molon labe
Patrick
Molon labe
- John Jackson
- Senior Member
- Posts: 161
- Joined: Jul 19th, '06, 22:39
- Location: Point Pleasant Beach, NJ
Capt. Patrick:
Wow! This just proves that when there is a will there is a way! How the heck did you come up with the game plan for that project? How many hours did it take? Is there any chance of the fiberglass delaminating from the aluminum? Any interest in doing another one?
I like the way the slightly larger frames look on the boat. I have redone my whole boat, but the windows, while I doctored them up to a point of acceptability, are not on a par with the rest of the boat. I had a welder fill in the holes on the curved window outside rims and that part came out pretty good. I bolted it from the outside, and the screw heads don’t really offend me, although the clean t-bolt from the inside way does look much better. To disguise the condition of the windows on the Hound I had my canvas guy make a front windshield cover that is clear with white over the frames and from a little distance it makes it look like the frames are a little fatter and I think it improves the appearance a little. Plus it has stopped all the leaks. Maybe I will take a crack at doing what you did over the winter. I will try and take some pictures of my "quick fix" and send it to you.
PS. Are you going to Atlantic City?
Wow! This just proves that when there is a will there is a way! How the heck did you come up with the game plan for that project? How many hours did it take? Is there any chance of the fiberglass delaminating from the aluminum? Any interest in doing another one?
I like the way the slightly larger frames look on the boat. I have redone my whole boat, but the windows, while I doctored them up to a point of acceptability, are not on a par with the rest of the boat. I had a welder fill in the holes on the curved window outside rims and that part came out pretty good. I bolted it from the outside, and the screw heads don’t really offend me, although the clean t-bolt from the inside way does look much better. To disguise the condition of the windows on the Hound I had my canvas guy make a front windshield cover that is clear with white over the frames and from a little distance it makes it look like the frames are a little fatter and I think it improves the appearance a little. Plus it has stopped all the leaks. Maybe I will take a crack at doing what you did over the winter. I will try and take some pictures of my "quick fix" and send it to you.
PS. Are you going to Atlantic City?
Who is online
Users browsing this forum: Grande and 26 guests