bertram31.com

Joseph Fikentscher

I use Navionics on my iPhone when I am on someone else's boat such as a head boat. I mark where we stop to fish and transfer the coordinates to my Simrad NSS8 when I get to my boat. I really like the Simrad better than my last (smaller) Garmin. https://www.facebook.com/enduranceb25/photos/a.82806320...

Joseph Fikentscher

Finally got it back together yesterday. Seems to be ok. Ran in the slip only. How long does the red lock tite take to set up?

I figure I’ll take it out tomorrow for a run.

Thanks for the offer Tony.

Joseph Fikentscher

After 5 hours, I still can't line this up. UGH!!! It should just slide in.

Joseph Fikentscher

Got it back from the machine shop early. $80.

Lining up the splines is no fun. Taking a break. It's quite heavy.

https://www.facebook.com/enduranceb25/p ... =3&theater

Joseph Fikentscher

When it is working.
https://www.facebook.com/enduranceb25/p ... =3&theater

Joseph Fikentscher

I vote for cold ones and fish stories. I used to be able to catch fish.

Joseph Fikentscher

Thanks guys. Wont get it back till next week, so another weekend of no fishing. I'll update when I have progress.

Joseph Fikentscher

Tom, Thanks but I just took it to a machine shop so they can get the bolts out.

Joseph Fikentscher

I am assuming if I redrill and tap, the bolt size would be larger. Would that give me more strength?

Joseph Fikentscher

https://www.facebook.com/enduranceb25/p ... =3&theater

tried heat and an easy out. No luck yet on the last two bolts.
https://www.facebook.com/enduranceb25/p ... =3&theater

Joseph Fikentscher

Carl, only the trans coupling is threaded. The shaft coupling is not. There is only enough room for about 1/4 inch on the rear of the shaft coupling.

Joseph Fikentscher

No, I did not use Loctite. Just the bolts and lock washers.

Joseph Fikentscher

Condolences.

Joseph Fikentscher

Well, here I go again. Same side, same problem. The shaft coupling bolts sheared off again. This time I was only going about 6 knots around 1200 rpm. Could only get two of the bolts out. the other two broke flush at the trans coupler. As before, no room to work. Had to cut the deck a bit to raise th...

Joseph Fikentscher

Looking great Cam!!!

Joseph Fikentscher

Does this help?

http://www.fourforty.com/techstuff/ignition.html

Joseph Fikentscher

https://www.facebook.com/photo.php?fbid ... =3&theater

Joseph Fikentscher

Pete Gibbons (on Facebook) in the Seattle area has twin Yanmars, I think 190HP with v-drives. Ill look for a link.

Joseph Fikentscher

I have the Simrad RS12. Works ok. Negatives: Hard to see, No keypad for changing channels, No AIS. But sends and receives good. Would have bought the RS35 at this price.

Joseph Fikentscher

The PO of my boat said the distributors were getting damp and causing the engines to shut down. Actually, the coils were the culprit, they would get hot as the engine ran and the start to break down. I finally replaced them, and the problem went away. I have since had to replace the port coil twice....

Joseph Fikentscher

Beautiful!!

Joseph Fikentscher

I have a friend in Florida selling his 25 Flybridge. $12k. Newly painted topsides, rebuilt engines etc.

https://www.facebook.com/search/top/?q= ... SEARCH_BOX

Look under posts to find the one I shared.

Joseph Fikentscher

Dr. Infantolino was my Cardiologist, but retiring now.

Joseph Fikentscher

https://www.facebook.com/enduranceb25/p ... =3&theater

Joseph Fikentscher

Ran my IO for 20 years. Zero problems. Regular maintenance should be done. Remove every year and lube, change oil, check impeller.
Went through 2 props and a couple of routine hose changes.

Joseph Fikentscher

https://www.boatoutfitters.com/hardware ... r-hardware

Joseph Fikentscher

I used Jaeger Lumber in Belmar, NJ.

Joseph Fikentscher

I used AZEK sheet. I think 1/4 inch., Maybe 3/8. About $90/sheet 4x8.

Joseph Fikentscher

I've been watching his progress. Interesting. Always looking for new ideas.

Joseph Fikentscher

I don't think aluminum is for salt water. I would use zinc.

Joseph Fikentscher

https://www.dropbox.com/s/xbg39fa0q1lel ... M.jpg?dl=0

My Bud trying not to spill a drop! Drinks for the wives and crew.

Joseph Fikentscher

Cam, I posted pics on Facebook. The original tabs are cut on an angle and are 17 1/2" at the rear of the tab. They are 8" deep. The new ones I bought are I think 12x12, but they are currently buried somewhere in the garage. When (If) I can find them I will measure. You have about 14" where they are ...

Joseph Fikentscher

Yannis, I don't think they need much service. Keep the hydraulic fluid at the correct level. ( will stay there unless you have a leak) Check the hoses periodically. Don't paint the actuators. Periodically check the electrical connections. In other words, keep an eye on them as you would the rest of ...

Joseph Fikentscher

Cam,

New computer, can't seem to find a good pic, but mine are almost exactly like John's.

Joseph Fikentscher

Im using InstaTrim because that is what was on the boat when I bought it. Picked up a new kit on eBay for a reasonable price. New pump, New actuators, New hosing, New switch and wiring. Works great. I have new stainless tabs, but used the ones already on the boat, keeping them in case I damage a tab...

Joseph Fikentscher

Keith Poe trailers his 31 in California all the time. Maybe he will chime in or you can PM him.

Joseph Fikentscher

[img]Image%20link%20goes%20here[/img]

First click the IMG in the header. Your image url goes between the brackets. Same for a url link to a website.

Joseph Fikentscher

Sent today.

Joseph Fikentscher

GO PRO on all the time.

Joseph Fikentscher

If you cut the transom out you could add 3 more feet of boat!!

Just dreaming at the desk today.

Joseph Fikentscher

I have not found the tag yet on my '68.

https://www.dropbox.com/s/cnm1divnpgni7 ... 3.png?dl=0

Joseph Fikentscher

Check Coco's on Facebook.

Joseph Fikentscher

My '68 has two tanks and a center stringer. V-drive version. Tanks are under the cabin stepdown.

Joseph Fikentscher

I have 2 alunimum tanks 50gal each. Vdrive inboards.

Joseph Fikentscher

Tony, you crack me up!

Joseph Fikentscher

Very nice! Can't wait to see them installed.

Joseph Fikentscher

Same problem, but mine was a cracked 50amp fuse with the reset button. Engine would start, shut off when warm, and start again after cooling down. Bugger of a time finding the culprit.

Joseph Fikentscher

Before fueling, close every window, hatch, and door. After fueling open every window, hatch, door, engine box and run blowers. After starting close engine boxeses and anything else you want closed.

Joseph Fikentscher

Wow!! Beautiful!

Joseph Fikentscher

Amen.

Search found 575 matches